Teletronics EzBridge 5800 Uživatelský manuál

EzBridge 5800 User Manual 500mW

LED Status Function On Power on. Power Off No power. Blinking Blinking: Wireless LAN is transmitting. On On: Wireless LAN connection is active.

Configuring Windows for IP Networking To establish a communication between your PCs and the EzBridge 5800, you will need to set up a static IP addres

Note: Again the IP address must be in the format of 192.168.1.x. Where the value of X should be ranged from 1 to 254 excluding 99. 5. Click OK, and th

Note: Again the IP address must be in the format of 192.168.1.x. Where the value of X should be ranged from 1 to 254 excluding 99. 5. Click OK. 2.6

3. Select the Internet Protocol (TCP/IP) for your network card, and then click Properties. 4. In the opened dialog box, choose Use the following I

Note: Again the IP address must be in the format of 192.168.1.x. Where the value of X should be ranged from 1 to 254, excluding 99. Click OK.

Web Configuration Interface 3.1 Client Bridge Mode Default IP Address in Client Bridge Mode: 192.168.1.99 To access the web control interface ple

Info Firmware Revision Current firmware revision loaded on the EzBridge. Connected to SSID SSID in which the EzBridge is associated to. Using Ch

Configuration

Operation Mode Ad-hoc: An 802.11 networking framework in which devices or stations communicate directly with each other, without the use of an access

No part of this documentation may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation,

64-bit WEP with 10 hexadecimal digits ('0-9', 'A-F') Key1= 0x123456789A Key2= 0x23456789AB Key3= 0x3456789ABC Key4= 0x456789ABCD

Stations Bridge Table The bridge table is a list of all devices connected to the EzBridge through the Ethernet side. Information such as IP and M

Administration

User name This is the name of the user account that will be used to configure the EzBridge. (Default User name: blank) Administrator password The p

The factory gateway default address is 192.168.1.1 Device name This is the name that the bridge will use to identify itself to external configuratio

3.2 Access Point Mode Default IP Address in Access Point Mode: 192.168.1.90 To access the web control interface please open up a browser window and

Info Firmware Revision Current firmware revision loaded on the EzBridge. MAC address of Access Point The MAC address of the wireless card plugged

Configuration Access point name You can name this access point for identification. You can leave it blank without entering anything. However, th

Channel 1 = 2401 Hz – 2423 Hz Channel 6 = 2426 Hz – 2448 Hz Channel 11 = 2451 Hz – 2473 Hz Americas: Wireless Channels 1-11 Asia: Wireless Channels 1

MAC Filter Enable access control If enabled, this feature will allow you to associate devices by MAC addresses from up to 16 different units. Any

Table of Contents Introduction ……………….……………………………...…..……………...4 1.1 Features ……………………………………...…………….………4 1.2 Specifications ……………………………...………………

Advanced Maximum associated stations This the maximum number of wireless clients that can be associated at any one time. Fragmentation threshol

sleep mode, alerting the device to a packet awaiting delivery. A DTIM interval, also known as a Data Beacon Rate, is the frequency at which an access

Encryption WEP enabled Short for Wired Equivalent Privacy, a security protocol for wireless local area networks (WLANs) defined in the 802.11b st

128-bit WEP with 13 characters Key1= 2e3f4w345ytre Key2= 5y7jse8r4i038 Key3= 24fg70okx3fr7 Key4= 98jui2wss35u4 128-bit WEP with 26 hexadecimal digi

Admin User name This is the name of the user account that will be used to configure the EzBridge. (Default User name: blank) Administrator passwo

The components of SNMP network management fall into three categories: 1. Managed devices (such as a switch) 2. SNMP agents and MIBs, including Remot

If enabled the MAC Address from the first Ethernet client that transmits data through the EzBridge will be used. This will mean that the client MAC a

Appendix A: Warranty Policy Limited Warranty All Teletronics’ products warranted to the original purchaser to be free from defects in materials and wo

Appendix B: RMA Policy Product Return Policy It is important to us that all Teletronics’ products are bought with full confidence. If you are not 10

Appendix C: Regulatory Information Statement of Conditions We may make improvements or changes in the product described in this documentation at any

Introduction The 802.11b EzBridge 5800 aims to fill in the gap between regular 2.4 GHz and that of 5.8 GHz equipment. It combines the ease and relia

With the Conformité Européene (CE) and European standards and amendments, we declare that the equipment described in this document is in conformance w

Appendix D: Contact Information Need to contact Teletronics? Visit us online for information on the latest products and updates to your existing pr

Appendix E: Important Outdoor Install Guide This EZBridge unit requires additional grounding and protection prior to installation to ensure trouble f

Appendix F: EzBridge Model Information and Compatible Teletronics Wireless Cards EzBridge has t

Appendix G: Troubleshooting Please check the following If you no longer can access the EzBridge through the web interface: 1. Clear out the arp (typ

Appendix H: Glossary 802.1x - The standard for wireless LAN authentication used between an AP and a client. 802.1x with EAP will initiate key handli

network and other users through an access point; this is the typical way corporate WLANs work. An alternative is ad-hoc mode, but users would have to

UDP (User Datagram Protocol) - A communication method (protocol) that offers a limited amount of service when messages are exchanged between computer

Receive Sensitivity • 1 Mbps: –94 dBm • 2 Mbps: –91 dBm • 5.5 Mbps: –87 dBm • 11 Mbps: –84 dBm Available Transmit Power Settings 100 mW /

Warranty UDC 5800HM Frequency Band to Ant 5725 - 5850 MHz Frequency Band to Radio 2400 - 2500 MHz Local Oscillator Frequency 3328 MHz Frequency Sta

1.3 Product Kit The EzBridge 5800 Kit contains the following items: • One EzBridge 802.11b PCB • One UDC 5800 • Two Power Extractor (One 7.5 VDC

1.5 Assembly Diagram *Part pictures will vary, please use it only as a general guide line. 1.6 Default Factory Software Settings AP (Unit on the

EzBridge 802.11B Basics This section is consisted of three parts. You will learn the guise of the hardware, including the ports and LEDs, and the ins